How To Reset Honeywell Water Heater 7 Flashes

In the United States, Honeywell makes many products in and out of the domicile, From motion detectors to navigation systems for airlines. Honeywell also makes water heater control valves that are used on several h2o heater brands.

When faced with a hot water supply issue, the first troubleshooting step is unremarkably to reset the unit of measurement. But frustration ensues when you cannot figure out how to get that done.

I had the same frustration as you practise when trying to locate Honeywell water heater reset push.

Just it is important to note that manufacturers make reset buttons hard to admission to prevent accidental activation.

This article will show yous how to activate the Honeywell water heater reset button system.

Where is the reset button on a Honeywell Water Heater

The Reset Button on the Honeywell Water Heater is the pilot light knob. Yous can reset the water heater by lighting the pilot and turning the knob to "very hot" for ten seconds, "hot" for ten seconds and to "airplane pilot" for ten seconds. Your lawmaking calorie-free volition begin blinking normally

Most water heaters have a reset push button which is usually establish underneath a metallic cover in the middle of the water tank. The Honeywell H2o Heater is different in this regard.

Honeywell Hot Water Heater Control Valve

How to Reset Your Honeywell Water Heater

When y'all go far at your water heater, you will detect that the code lite is either blinking abnormally or permanently on, indicating that there is a fault.

You tin reset your Honeywell hot Water heater in iv steps.

Head to you hot water tank and brand sure that the airplane pilot light turned on.
Turn the pilot light knob to the "very hot" position for 10 seconds.
Plough the airplane pilot low-cal knob to the "hot" position for x seconds.
Turn the pilot low-cal knob to the "airplane pilot" position for 10 seconds

At the end of this sequence, the pilot light will begin blinking over again.

Why is My Honeywell Hot Water Heater Tripping the Reset Button?

Honeywell designs its heater reset buttons to trip equally a safety precaution. When the water temperature rises in an uncontrolled style, the reset button is tripped.

Here are some reasons why the reset button may trip.

Bad Heating Element

The heating element is responsible for raising the temperature of the water in the tank.

If it is damaged or has a short in it, the temperature of the water will continue to rising. This triggers the reset button to trip because it is unable to communicate with the thermostat.

To resolve this effect, a replacement heating chemical element may be required.

Pair of two corroded hot h2o heater elements.

Faulty Thermostat

The thermostats in the water heater are responsible for monitoring the temperature in the tank.

It operates past delivering signals to the heating element, which either turns on to boost the temperature or turns off to lower it.

If the thermostat fails, information technology is unable to perform its part, causing the reset button to trip since there is no communication between the thermostat and the heating element.

Electric Bug (Bad or loose Wiring and Circuit breakers)

Electrical bug are a mutual cause for the Honeywell h2o heater's reset button to trip. I normally start past looking for faulty wiring and damaged circuit breakers.

The reset button might be tripped by loose wires. In many circumstances, yous can run across when there is an event with the wiring of your unit's components. You may detect burnt pieces, or when you delicately pull on a wire, it may entirely detach from the component to which information technology is attached.

Circuit breakers deteriorate as they age as well. When you open your electric panel, you may notice that they are hot to the touch, and you may fifty-fifty odour burning.

Checking for and removing electrical problems as a possible reason of your unit'southward reset button tripping is an important footstep in the troubleshooting process.

What setting should my Honeywell Water Heater exist on

Your Honeywell h2o heater should exist set up at a temperature of 120 degrees Fahrenheit. This is the temperature recommended by the department of energy.

This temperature maximizes the balance between what is needed for most domicile uses and decision-making your energy costs. The hotter the temperature, the more energy is required to maintain that temperature considering your h2o heater volition need to bike on and off more frequently.

Honeywell Hot H2o Heater Control Settings

The Honeywell H2o Heater has the following Temperature Settings

Depression	90 degrees
Hot	120 degrees
A	130 degrees
B	140 degrees
C	150 degrees
Very Hot	160 degrees

Honeywell Hot Water Heater Settings

One thing I take noticed is that the temperature setting at the water heater can be very different from the temperature at the signal of use. Heat losses can occur all through your piping organization. It is important to keep this in mind and use a thermometer to determine if the temperature is where you expect it to exist.

How to Turn Up Honeywell H2o Heater

The Honeywell Command Valve has three settings, A, B, C on the pilot light knob to control the maximum temperature of the h2o heater.

To alter the maximum temperature on the water heater, plow the dial up from A to B or to C. It is important to expect for at least xxx minutes for the switch in temperature to take full effect. It takes the heating elements that much fourth dimension afterwards the dial is adjusted to rut upwards the h2o that is in the tank.

Does a Honeywell Water Heater Thermostat Have a Bombardment

No. The Honeywell H2o Heater Thermostat/Gas Valve is not powered past a battery. The thermostat is powered past a thermocouple. The thermocouple works past converting oestrus it generates in to electricity.

Thermocouple – Photo Credit Grainger Supply House

The estrus is generated equally a effect of the deferential in conductivity that occurs within the thermocouple. That differential causes electrical current to period which in turn powers the thermostat.

Honeywell H2o Heater Reset

Resetting your Honeywell Water Heater is relatively easy once you realize that at that place is no reset button. Make sure that the pilot is turned on, switch the dial to "very hot" for x seconds, to "hot" for ten seconds and to "pilot" for 10 seconds. This will reset your h2o heater.